; NOTE: the following CSI logger program annotations may contain errors. ; From an experimental perl module, Campbell::Program, by fnkci@uaf.edu ; output generated on host shand at Fri May 9 14:06:54 2008 local time MODE 13 13:00 1 01:} MODE 14 MODE 1 SCAN RATE 5 1:P10 ; BATT VOLT 1:1 ; store in location 1 2:P17 ; INTERNAL TEMP 1:2 ; store in location 2 3:P3 ; PULSE 1:1 ; 1 repetition 2:1 ; from pulse counter P1 3:21 ; as low level AC, discard long interval counts, output frequency (Hz) 4:8 ; store result in location 8 5:.098 ; with multiplier * 0.098 6:0 ; and with offset + 0 4:P4 ; EX-DEL-SE 1:1 ; 1 repetition 2:5 ; using 2500 mV range, slow integration 3:6 ; from input channel SE6 4:1 ; drive excitation channel E1 5:1 ; with delay 0.01 sec 6:2500 ; with 2500 mV excitation 7:7 ; store result in location 7 8:.142 ; with multiplier * 0.142 9:0 ; and with offset + 0 5:P92 ; IF TIME 1:0 ; is 0 minutes into 2:1 ; 1 minute interval 3:30 ; then DO... 6:P86 ; DO 1:41 ; set port C1 high 7:P22 ; EXCIT w/DEL 1:1 ; drive excitation channel E1 2:0 ; delay 0 sec w/ excitation 3:15 ; delay 0.15 sec after excitation 4:0 ; with 0 mV excitation 8:P1 ; VOLT (SE) 1:1 ; 1 repetition 2:5 ; using 2500 mV range, slow integration 3:1 ; from input channel SE1 4:3 ; store result in location 3 5:.1 ; with multiplier * 0.1 6:-40 ; and with offset + -40 9:P1 ; VOLT (SE) 1:1 ; 1 repetition 2:5 ; using 2500 mV range, slow integration 3:2 ; from input channel SE2 4:4 ; store result in location 4 5:.1 ; with multiplier * 0.1 6:0 ; and with offset + 0 10:P86 ; DO 1:51 ; set port C1 low 11:P95 ; END IF-DO 12:P92 ; IF TIME 1:0 ; is 0 minutes into 2:15 ; 15 minute interval 3:30 ; then DO... 13:P105 ; SDI-12 RECORDER 1:0 ; address 0 2:0 ; command M, initiate measurement 3:2 ; port C2 4:9 ; store result in location 9 5:1 ; with multiplier * 1 6:0 ; and with offset + 0 14:P30 ; Z=F*10^exp 1:273.15 ; fixed value 273.15 2:0 ; times 1 (10^0) 3:5 ; store 273.15 in location 5 15:P33 ; Z=X+Y 1:3 ; X value from location 3 2:5 ; Y value from location 5 3:11 ; store sum in location 11 16:P38 ; Z=X/Y 1:11 ; X value from location 11 2:5 ; Y value from location 5 3:6 ; store ratio in location 6 17:P39 ; Z=SQRT(X) 1:6 ; X value from location 6 2:6 ; store square root in location 6 18:P36 ; Z=X*Y 1:9 ; X value from location 9 2:6 ; Y value from location 6 3:10 ; store product in location 10 19:P95 ; END IF-DO 20:P92 ; IF TIME 1:0 ; is 0 minutes into 2:15 ; 15 minute interval 3:10 ; set output flag F0 high, output array id 120 21:P77 ; REAL TIME 1:1220 ; year + day(midnight=prev.day) + hour-minute(midnight=2400) 22:P71 ; AVERAGE 1:2 ; 2 repetitions 2:1 ; value from location 1 23:P71 ; AVERAGE 1:2 ; 2 repetitions 2:3 ; value from location 3 24:P69 ; WIND VECTOR 1:1 ; 1 repetition 2:60 ; 60 scans for standard deviation subinterval 3:0 ; avg spd, avg dir, std dev of dir (Yamartino), for anem. & vane 4:8 ; wind speed from location 8 5:7 ; wind direction from location 7 25:P73 ; MAXIMUM 1:1 ; 1 repetition 2:0 ; output value only 3:8 ; value from location 8 26:P71 ; AVERAGE 1:2 ; 2 repetitions 2:9 ; value from location 9 27:P96 ; SERIAL OUT 1:71 ; storage module 1 28:P86 ; DO 1:20 ; set output flag F0 low 29:P20 ; PORT SET 1:7999 ; P8=output, P7=nc, P6=nc, P5=nc 2:9999 ; P4=nc, P3=nc, P2=nc, P1=nc 30:P92 ; IF TIME 1:0 ; is 0 minutes into 2:60 ; 60 minute interval 3:30 ; then DO... 31:P89 ; IF X < = > F 1:1 ; if X from location 1 2:4 ; is < 3:11.8 ; fixed value 11.8 4:21 ; set flag F1 low 32:P89 ; IF X < = > F 1:1 ; if X from location 1 2:3 ; is >= 3:11.8 ; fixed value 11.8 4:48 ; set port C8 high 33:P95 ; END IF-DO 34:P92 ; IF TIME 1:720 ; is 720 minutes into 2:1440 ; 1440 minute interval 3:48 ; set port C8 high 35:P91 ; IF FLAG/PORT 1:21 ; if flag F1 is low 2:30 ; then DO... 36:P92 ; IF TIME 1:10 ; is 10 minutes into 2:60 ; 60 minute interval 3:58 ; set port C8 low 37:P95 ; END IF-DO 38:P89 ; IF X < = > F 1:1 ; if X from location 1 2:4 ; is < 3:11.8 ; fixed value 11.8 4:24 ; set flag F4 low 39:P89 ; IF X < = > F 1:1 ; if X from location 1 2:3 ; is >= 3:12 ; fixed value 12 4:14 ; set flag F4 high 40:P92 ; IF TIME 1:960 ; is 960 minutes into 2:1439 ; 1439 minute interval 3:30 ; then DO... 41:P91 ; IF FLAG/PORT 1:13 ; if flag F3 is high 2:14 ; set flag F4 high 42:P91 ; IF FLAG/PORT 1:14 ; if flag F4 is high 2:44 ; set port C4 high 43:P91 ; IF FLAG/PORT 1:24 ; if flag F4 is low 2:54 ; set port C4 low 44:P86 ; DO 1:23 ; set flag F3 low 45:P95 ; END IF-DO 46:P0 ; NOP MODE 2 SCAN RATE 0 MODE 3 1:P0 ; NOP MODE 10 1:28 2:64 3:0 4:1097729 5:2048 MODE 12 1:0 1:0 1:0 MODE 13 13:8 8:0 MODE 13 13:9 9:0 MODE 13 13:10 10:0 MODE 13 13:13 13:0 MODE 11 1:59009 2:4573 3:2304 4:0 5:0 6:1 7:13 8:3.1072 9:11 10:0 11:4.625 ;; CAUTION: experimental output tags follow: ;; ;; output array: ;; 1. id_120 ;; 2. year ;; 3. day ;; 4. hhmm ;; 5. average-Loc1.logger_battery_voltage ;; 6. average-Loc2.panel_temperature_C ;; 7. average-Loc3.SE1 ;; 8. average-Loc4.SE2 ;; 9. vector_avg_spd-Loc8.P1 ;; 10. vector_avg_dir-Loc7.SE6 ;; 11. vector_dir_std_dev ;; 12. maximum-Loc8.P1 ;; 13. average-Loc9 ;; 14. average-Loc10